| Model | C6 1/2 36C | ||
| Processing capacity | Max swing diameter over bed | 360 | |
| Max.swing over cross slide | 190 | ||
| Maximum turning diameter at the saddle Maximum turning diameter at the saddle
| 520 | ||
| Center distance | 750, 1000, 1500 | ||
| Width of bed | 360mm | ||
| Spindle | Spindle bore | Φ52/80mm | |
| Spindle nose | C6 | ||
| Spindle taper | MT6 | ||
| Spindle speeds range（Steps） | 40-1400 (9steps) | ||
| Feed | Metric threads（Number ） | 0.25-14mm (19kinds) | |
| Inch threads（Number ） | 2-40/inch | ||
| Modular threads（Number ） | 0.25-3.5mπ (11kinds) | ||
| Carriage | Cross slide stroke
Cross slide stroke
| 180mm | |
| Tool rest stroke Small tool rest stroke
Small tool rest stroke
Small tool rest stroke
Small tool rest stroke
Small tool rest stroke
Small tool rest stroke
Small tool rest stroke
| 95mm | ||
| section dimension
| 20 x 20mm² | ||
| Tailstock | Taper of tailstock sleeve | MT4 | |
| Diameter of tailstock sleeve | 65mm | ||
| Stroke of tailstock sleeve | 140mm | ||
| Main motor | 4kw | ||
| Package size: (L x W x H) |
| ||
| Center distance 750mm | 2220 x 1150 x 1590mm | ||
| 1000mm | 2470 x 1150 x 1590mm | ||
| 1500mm | 2970 x 1150 x 1590mm | ||
| Weight: NW/GW（KG） |
| ||
| Center distance 750mm | 1350 | 2000 | |
| 1000mm | 1450 | 2100 | |
| 1500mm | 1600 | 2250 | |
1. Environmental requirements for the location of the machine tool: The location of the machine tool should be far away from the source of vibration, direct sunlight and thermal radiation, and moisture and airflow should be avoided. If there is a vibration source near the machine tool, an anti-vibration trench should be set around the machine tool. Otherwise, it will directly affect the machining accuracy and stability of the machine tool, and cause poor contact of electronic components, failures, and affect the reliability of the machine tool. To 2. Power requirements: Generally, lathes are installed in the machining workshop, which not only has large environmental temperature changes and poor use conditions, but also has a lot of electromechanical equipment, which causes large fluctuations in the power grid. Therefore, the location where the ordinary lathe is installed requires strict control of the power supply voltage. The power supply voltage fluctuation must be within the allowable range and remain relatively stable. Otherwise it will affect the normal operation of the CNC system. 3. Temperature conditions: The ambient temperature of the general bed is less than 30 degrees Celsius, and the relative temperature is less than 80%. Generally speaking, an exhaust fan or air cooler is arranged inside the numerical control electric control box to keep the electronic components, especially the central processing unit's working temperature constant or the temperature difference changes very small. Excessive temperature and humidity will reduce the life of control system components and cause more failures. The increase in temperature and humidity and the increase in dust will cause adhesion on the integrated circuit board and cause short circuits. 4. Use the machine tool as specified in the manual: When using the machine tool, the user is not allowed to change the parameters set by the manufacturer in the control system at will. The setting of these parameters is directly related to the dynamic characteristics of each part of the machine tool. Only the value of the gap compensation parameter can be adjusted according to the actual situation. The user cannot replace the machine tool accessories at will, such as using a hydraulic chuck that exceeds the specification. When setting up accessories, the manufacturer fully considers the matching of various link parameters. Blind replacement causes mismatch of various link parameters, and even causes unexpected accidents. The pressure of the hydraulic chuck, hydraulic tool rest, hydraulic tailstock, and hydraulic cylinder should be within the allowable stress range, and any increase is not allowed.
